 |
|
 |
|
| |
| Welcome to Yuehua Sanitary Ware Co.,Ltd.,
If you have any interest on our products or any comments
for us, please send us a email: |
|
|
Massage Bathtub :
Breakdown
phenomenon and settlement: |
| Phenomenon |
Reasons |
Maintenance |
| No power or electricity leaking protection device
is activated |
1. Electricity leaking protection device cut off
power source when electricity line is not well
connected.
2. Power or electricity circuit have phenomenon
of electricity leaking. |
1. check and reconnect the wiring system.
2. check the power source, electricity
circuit and ground line. |
Water Jets are
not working. |
1. check the system whether is on.
2. the impeller of water pump doesn't rotate.
3. water pump is broken which caused by
working without water coming in. |
1. turn on the system.
2. check through and remove the garbage
which is inside the pump. Switch pipe
can be removed.
3.install a new water pump |
The intensity of
hydro-massage
cannot be adjusted |
1. water pump's suction has not enough power.
2. air adjustment valve is abnormal.
3. jets or nozzles are blocked. |
1. check the water pump whether is working normally
2. change the air adjustment valve.
3. remove things which are blocking the jets. |
Water leaks from
the pipes
|
1. seal ring is broken.
2. screws doesn't lock tightly.
3. pipes doesn't seal properly. |
1. chang seal ring.
2. lock the screws tightly.
3. re-seal the silicone.
4. change water pipe |
Jets shower can
not be work. |
1. voltage is abnormal
2. Switch cannot be work
3. control panel cannot be work.
4. water in electromagnetism valve is be blocked |
1. please use it at the normal situation of voltage.
2. check and change the switch.
3. maintain and change the control panel.
4. get rid of mess of the jets. |
| No lighting |
1. The bulb is broken.
2. power line is disconnected.
3. control panel is broken. |
1. change a new bulb..
2. re-connect the circuit..
3. maintain or change control panel |
| Cleaning and Maintenance: |
1. The daily maintenance should be cleaned
with ordinary detergent and soft cloth. Please do not
use the detergent which contains acetone or ammonia
liquid. If there marks or something like glue on the
surface of bathtub, just polish it with soft cloth dipping
with gas.
2. If there are scratches on bathtub surface, please
polish it with 1500# frosted paper dipping with liquid
and burnish it with toothpaste. It will be shining again
after that.
3. If there are furring on the surface of bathtub, it
can be take away by mild acid detergent, for example
wipe the bathtub with lemon juice or vinegar which be
heated.
4. Do not wipe the chrome plated spare parts all the
time, and do not get in touch with chemical detergent
etc. Otherwise the surface of chrome plated will be
destroyed. The product should be clean by soft cloth
other than coarse cloth.
5. To check the water pipe regularly in order to avoid
troubles from crack of water pipes or blocked inside.
6. If there are something such as hair stuck inside
the jets, then just to twist out the jets and remove
it.
7. To clean hydro-massage equipment: To full fill hot
water which is 40'C, and pour 2g/L detergent, start
hydro-massage function more than 5 minutes, then turn
off the massage function and drain out the water. Next,
to full fill cold water and start hydro-massage function
for 3 minutes, then turn off the massage function and
drain out the water, at last, to dry the bathtub with
towel.
8. Filter should be clean once a week.
9. Keep out from combustibles and goods which over 80°C
to avoid fire disaster and damage the product.
10. The bathtub should be transported carefully. Do
not lay heavy things on it and do not bump and shaking
the tub. If the bathtub has not been used for a long
time, drain out the water of the bathtub and keep it
in a dry and ventilate environment. Avoid corrosive
gas. |
[ Page(1) |
Page(2) ] |
|
